Home > Blog > Content

Common Faults and Solutions of Bridge Cranes

Jun 15, 2025

Bridge cranes are widely used lifting equipment in industrial and construction fields. Below, based on common faults of bridge cranes, corresponding solutions and precautions will be provided.

info-3904-2928


The crane fails to start.
Solution:
1) Check if the power supply is normal and if there is electricity.
2) Check whether the cables are in good contact;
3) Check whether the controller is functioning properly and if there are any faults.
4) Check if the motor is functioning properly and if there are any faults.
When checking the power supply and cables, pay attention to safety to avoid electric shock accidents.

The crane failed to operate normally after being started
Solution:
1) Check if the motor is functioning properly and if there are any faults.
2) Check whether the transmission system is normal and if there are any faults.
3) Check whether the controller is functioning properly and if there are any faults.
When inspecting the motor and transmission system, pay attention to safety to avoid being pinched or colliding.

Abnormal noises occurred during the operation of the crane
Solution:
1) Check whether the transmission system is normal and if there are any faults;
2) Check whether the wheelset is normal and if there are any faults.
3) Check whether the crane structure is loose.
When inspecting the transmission system and wheel set, safety should be given due attention to avoid being pinched or colliding.


Shaking occurs when the crane is in operation
Solution:
1) Check whether the transmission system is normal and if there are any faults;
2) Check whether the wheelset is normal and if there are any faults.
3) Check whether the crane structure is loose.
When inspecting the transmission system and wheel set, safety should be given due attention to avoid being pinched or colliding.

There was a pause when the crane was running
Solution:
1) Check if the power supply is normal and if there is electricity.
2) Check whether the cables are in good contact;
3) Check whether the controller is functioning properly and if there are any faults.
4) Check whether the transmission system is normal and if there are any faults.


When checking the power supply and cables, pay attention to safety to avoid electric shock accidents.

Loose CAM plates: Loose CAM plates may be caused by wear or damage to the CAM plates.
Solution: Replace the CAM plate or repair the CAM plate.
Plastic breakage at the contact roller of the linkage console: Plastic breakage may be caused by plastic aging or insufficient plastic strength.
Solution: Replace the plastic or enhance its strength.
Excessive wear at the contact roller pin causes the handle to get stuck after returning to the zero position: Excessive wear at the contact roller pin may be caused by the wear or damage of the pin.
Solution: Replace the latch or repair it.
The handle gets stuck: The handle getting stuck might be caused by the mechanical structure inside the handle getting stuck.
Solution: Clean the mechanical structure inside the handle or replace the handle.
The gnawing of the wheels and the unequal height of the car: The gnawing of the wheels and the unequal height of the car may be caused by the wear or damage of the wheels.
Solution: Replace the wheels or repair them.
Slippage: Slippage may be caused by motor failure or brake failure.
Solution: Check if the motor and brake are faulty. If so, replace or repair them in a timely manner.

 

The above are some common faults of bridge cranes and their solutions. If you encounter problems when using a bridge crane, you can refer to these solutions. At the same time, we also suggest that you check the equipment for any obstacles, deformations, wear and other issues before use to ensure its normal operation.

Send Inquiry
Contact Us
    • Tel: +8615993097180
    • manager@catet.cn
    • Address 1: 1506,Building 3, No.35 Guangtian Road,Baoan District, Shenzhen

    • Address2: Room 808A, Building A, No. 4545, Songbai Road, Hewan Community, Matian Street,Guangming District, Shenzhen, China

    • The factory is located in Intelligent Equipment Industrial Park in Naoli Town, Changyuan City, Henan Province.